HOOD & COMPONENTS. Inner. Japan built. Outer.. 2018 Toyota Camry 2.5L A/T LE SEDAN

JAPAN BUILT. A device that is installed in the Hood that when removed allows any water to be removed from being inside the Hood panel. A rubber ring with a hole in the center which provides protection through which Hood Panel related components pass through. Material to provide protection from paint. Multi-Purpose Tape. Part cannot be reused/reinstalled. Seal used for the Hood. Included with: Step.

JAPAN BUILT. outer.

inner. JAPAN BUILT. Bump Stop used for the Liftgate. Rubber Cushion used to support and prevent the hood from rattling.

JAPAN BUILT. Clip that fastens hood seal to hood. Dashboard Panel Insulator Clip. Fender Clip. Hood Insulation Pad Clip. Part cannot be reused/reinstalled. Dashboard Panel. Fastener. Fender. Hood Insulation Pad. Protector. Retainer. Seal. Included with: Front seal, Insulator.

JAPAN BUILT.

JAPAN BUILT. Clip that fastens hood Seal to hood. Fender Closing Plate Clip. Radiator Support Access Cover Clip. Fender Closing Plate. Outer. Radiator Support Access Cover. Side. Sight shield fastener. To hood retainer. W'strip. Included with: Closing Plate, Front Seal, Front Seal Part cannot be reused/reinstalled, Front weatherstrip, Front weatherstrip Part cannot be reused/reinstalled, Seal, Seal strip, Seal to hood, Seal to Radiator Support, Seal to upper tie bar, Side Seal, Sight shield.

Left.JAPAN BUILT.

Left.JAPAN BUILT. Right.JAPAN BUILT. Automatic Transmission Oil Cooler Bolt. Belt Tensioner Bolt. Bolt that secures the hood hinge. Dash Panel Bolt. Engine Water Pump Bolt. Flange. Automatic Transmission Oil Cooler. Belt Tensioner. Dash Panel. Dash REINFORCED. Engine Water Pump. Hood Hinge. W'strip.

Right.JAPAN BUILT.

Left.JAPAN BUILT.

Right.JAPAN BUILT.

Left.JAPAN BUILT.

Right.JAPAN BUILT.

Left.JAPAN BUILT.

Left.JAPAN BUILT. Right.JAPAN BUILT. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Hood Support Rod to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Hood Support Strut Holder to it's mounting point. / Trunk Prop Rod. cylinder. Lift Stud. Strut. Windshield Washer. Bracket.

JAPAN BUILT.

JAPAN BUILT. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Hood Safety Catch to its mounting surface. Bolt that secures the Hood Latch. Hood Latch Striker Plate Bolt. Running Board Bolt. Windshield Washer. Center bracket. Hood Safety Catch. Hood Striker Plate. Lock cable. Mount. Running Board. Included with: Step bar assembly.

JAPAN BUILT.

JAPAN BUILT. A cover piece used to cover the hood latch on a vehicle. Fits over the Hood Latch to provide vibration dampening between the Hood Striker and the Hood Latch. Hood Latch Spacer. Part cannot be reused/reinstalled. HOOD NUT. Hood Insulator. Hood Spacer. Linkage shield. PROTECTOR.

JAPAN BUILT.

JAPAN BUILT. A part which fits around the Hood Release Cable and tightens, thereby securing the component in place with a Clamping force. Fuel Filler Door Release Cable Clip. Hood Release Cable Clip. Fuel Filler Door. Hood. Lever holder. Retainer. Included with: Release Cable.

JAPAN BUILT. A fastener to retain the Door Sill Plate to the vehicle. A part which fits around the Hood Release Cable and tightens, thereby securing the component in place with a Clamping force. Hood Release Cable Clip. Wiring HARNES. Door. Hood Cable. Retainer. Scuff. Trim.

black. JAPAN BUILT.

beige. JAPAN BUILT.

gray. JAPAN BUILT.

JAPAN BUILT.

JAPAN BUILT.